Shenzhen Nixi Technology Co., Ltd. welcomes you!
Nixi Technology

Shenzhen Nixi Technology Co., Ltd.

Ceramic capacitors, varistors, NTC thermistors, metallized film capacitors, X2 safety capacitors

Service Hotline

13798455373

13798433058

Shenzhen Nixi Technology Co., Ltd. Ceramic Capacitors | Varistors | NTC Thermistors | Monolithic Capacitors | Chip Safety Capacitors | Chip Varistors

NEWS

Ceramic capacitor
Varistor
NTC thermistor
SMD Chip Single Layer Ceramic Dielectric Capacitor
SMD Chip Varistors
Monolithic capacitors
Horizontal capacitor series
Non-inductive film capacitor series
Metallized Film Capacitor Series
Boxed film capacitor series

    Shenzhen Nixi Technology Co., Ltd.


    Address: No. 1221 Guangguan Road, Guanlan Street, Longhua District, Shenzhen City, Guangdong Province


    Contact: Mr. Li

    Tel: 13798455373, 13798433058


    Website: www.nixikj.com

    Email: lzf@nixi-cap.com


How to detect chip capacitors Technical Support

How to detect chip capacitors

Time:2022-01-05

How to detect chip capacitors? Recently, Baidu Know, Zhihu and other question-and-answer platforms have encountered many problems with chip capacitor detection. Many people are not familiar with chip capacitor detection, which leads to an increased chance of mistakes. Today, I'm going to tell you a little bit about it




    To measure the chip capacitance, you can use the multimeter R×1k or R×100 file to detect the capacitance greater than 0.047pF (the capacity is less than 0.047pF and can be measured with the R×10k file. But the multimeter has no response when the capacity is too small, and the pointer indicates at this time. It can be judged that the capacitor does not leak, but the capacity cannot be judged). When testing, connect the red and black test pens to the two ends of the capacitor respectively, and observe the swing angle of the needle. The greater the capacity, the greater the swing of the needle.




    After swinging to a certain value, it will go back to the vicinity of the maximum value. The larger the displayed value, the greater the leakage resistance of the capacitor. Generally, the normal electrolytic capacitor is hundreds of kΩ or more, and other capacitors are large. If the measured capacitance makes the needle swing similar to the normal capacitance (which can be compared and measured), and the leakage resistance is large, it indicates that the capacitance is good, otherwise it is abnormal.




    After one measurement, exchange the positions of the two test leads to measure again, which is convenient for comparing and judging the quality of the capacitor. For electrolytic capacitors, this can also determine its positive and negative poles: in the two measurements, the black pen with the largest leakage resistance is connected to the positive pole of the capacitor, and the red pen is connected to the negative pole. It should be noted that the reverse leakage resistance of some electrolytic capacitors is small, often tens to several kΩ, but the forward leakage resistance is basically normal. Most of these capacitors are products of poor quality or stored for too long, so do not use them.


    How to detect chip capacitors? Have you learned it? It is recommended that you look for an agent directly authorized by the original factory, such as chip capacitors, to buy or obtain samples of chip capacitors. It can not only ensure the quality consistency of samples and goods, but also obtain professional selection guidance from experienced technical engineers. They will give you professional support in terms of technology and purchasing convenience.


Contact Us


    Shenzhen Nixi Technology Co., Ltd.


    Address: No. 1221 Guangguan Road, Guanlan Street, Longhua District, Shenzhen City, Guangdong Province


    Contact: Mr. Li

    Tel: 13798455373, 13798433058


    Website: www.nixikj.com

    Email: lzf@nixi-cap.com


Nixi Technology
Copyright 2000-2022 Shenzhen Nixi Technology Co., Ltd.   粤ICP备2021178808号   Support: XXWQ 

Back to top